Don Allison Equipment is a Farm & Agriculture Equipment Dealer in Arley, Alabama

Delivery is

Business Hours: (cst)
Mon-Thurs  8am-5pm
Friday 8am-4pm
Saturday 8am-12pm

Call (800) 669-6450 for prices & more information
HayBuster H-1000 Series II Tub Grinder

  • Grinds Hay - big round bales, loose hay, small and large square bales
  • Grinds Crop Residues - straw, stover and other types
  • Grinds Grain - corn (ear or shelled & high moisture), sorghum
  • High Capacity in portable package
  • Electronic Governor
  • Works with 80 to 175 PTO horsepower tractors and all cereal grains
Call for Pricing and
Finance Options
18" wide by 20' long Stacking Conveyor
The product is taken away from the belly pan augers with a 18" wide by 20' long high-capacity stacking conveyor. The conveyor height is hydraulically controlled. A hefty hydraulic cylinder transmits its lifting force to the conveyor through a strong steel linkage system. It's all controlled by an easy push or pull of a simple hydraulic lever.
10' Tub at Flare
The "BIG BITE" tub measures 10 feet at the flare, 8 feet at the base, and has a depth of 44 1/2 inches.
BIG BITE Hammermill
The BIG BITE Hammermill is 44-1/2" long, and at operating speed, the hammers extend out to 26" in diameter. The 64 swinging hammers are arranged on eight heavy duty hammer rods. These hammers have four hardened cutting edges. When the hammer's cutting edge becomes worn it can be replaced by turning the hammer to the next available fresh, sharp cutting edge. The "BIG BITE" hammers can swing up to 180°, thus limiting how far the hammers can lay back under tough grinding conditions.
Tub Drive
The "BIG BITE" tub is driven by a hydraulic motor through a heavy-duty roller chain. This drive method provides for a responsive and smooth transition of power to the tub.
Electronic Governor
The tub rotational speed is controlled by the Duratech Electronic Governor. This electronic governor allows the engine speed to remain constant, as the tub rotation speed varies to control the feed rate to the hammer mill.
Eight Belt Drive System
A dependable Eight Belt Drive System routes power from the tractor's PTO and supplies it to the mill. This drive system turns the mill at approximately two times the tractor's PTO speed. This higher mill speed provides smooth feedind and delivers high capacity grinding.
High Capacity Augers
The two heavy-duty and high capacity augers mounted in the belly pan convey the product to the discharge conveyor. The auger and pan combination provides for a high-speed transfer of the product and for a clean, leak-free environment under the tub grinder.
Flexible Grinding Capabilities
Grinds Hay - big round bales, loose hay, small and large square bales
Grinds Crop Residues - straw, stover and other types
Grinds Grain - corn (ear or shelled & high moisture), sorghum, and all cereal grains
H-1000 Tub Grinder Specifications
Length 44-1/2"
Diameter (with hammers extended) 26"
Feed Opening 27" x 45"
Hammers (hardened swing) 3/8"
Number of Hammers 64
Rods (case hardened) 15/16"
Mill Plates 3/16" thick x 15-3/4" dia.
Mill Shaft (stress proof steel) 3"
Drive End Bearing (pillow block) 2-3/4"
Idle End Bearing (pillow block) 2-7/16"
Screens (hole sizes from 1/8" to 4") 1/4" thick
Screen Area 2,400 sq. in.
Drive PTO through multiple V belts
Type Double Free Floating Augers
Auger Size 9" x 96"
Width 33-3/4"
Drive Mechanical
Type Rubber Belt with Cleats
Drive Mechanical
Drive & Idler Roller Type "Easy Clean"
Length 20'
Width 18"
Maximum Conveyor Lift Height 13' 9"
Conveyor Lift Hydraulic
Conveyor Fold Hydraulic Fold Over Tub
Loading Height 8'
Tub Width at Flare 10' 3"
Depth 44-1/2"
Tub Inside Diameter at Base 8'
Tub Wall Thickness 14 gauge
Tub Floor Thickness 10 gauge
Drive Mechanism Electro/Hydraulic
Speed Control Electronic Governor
Type Double Free Floating
Auger Size 9" x 96"
Width 33-3/4"
Drive Mechanical
PTO HP Required 80 hp to 175 hp
Tub Rotation - 3 position hydraulic valve for clockwise, stop and counter-clockwise
Tub Speed - DuraTech model RCB93 Elecronic Governor stabilizes engine load by controlling tub rotation speed
Conveyor Lift - 3 position hydraulic valve for raise, hold & lower
Total 7,400 lbs
Width 10' 4"
Length 20' 2"
Height 9' 5"
Towing Arrangement Clevis type for hitch pin
Wheels Drop Center Rims
Bearings Tapered Roller Bearings
  • Loose Hay Guide
  • Grain Grinding Hopper
  • Ear Corn Kit
  • Geyser Plate
  • Mill Grate
  • Screen Sizes from 1/8" to 4" Round Hole
  • Highway Tires

  • Jay-Lor Mixers
  • Gehl Compact Excavactors, Skid Loaders, Telescopic Loaders, and Track Loaders
  • Claas Hay Equipment - Balers, Mowers, Rakes, and Tedders
  • Haybuster Bale Processors, Grain Drills, Mixers, Rock Pickers, and Roller/Hammer Mills
  • Manitou Telescopic Loaders and Forklifts
  • Stretch-o-Matic In Line Wrappers
  • SI Feeders Hay Wagons
  • Apache Equipment Trailers
  • Arrowquip Livestock & Cattle Handling Equipment
  • BBI Litter Spreaders
  • BushMaster Attachments - Mowers, Root Grapples, Pallet Forks, Round Bale Spears, Post Hole Diggers, and more
  • Bush-Whacker Rotary Cutters and Finishing Mowers
  • Calumet Spreader and Vacuum Manure Tanks
  • CID Attachments for Skid Steers - Augers, Buckets, Rakes, Grapples
  • Dion Forage Harvesters and Forage Boxes
  • Econoline Trailers
  • Henke Buffalo Mixers and Mills
  • H&S Manufacturing Agricultural Equipment
  • JBM Feed Wagons
  • Kelly Ryan Feed Wagons
  • Lifetime Wagons Hay and Feed Wagons
  • LVI Litter Processors
  • Miller Pro Forage Blowers, Forage Wagons, and Trailer Sprayers
  • Modern Ag Products
  • North American Implements
  • ProTank & Equipment
  • Ag-Bag Silage Baggers
  • Art's Way Grinder Mixers and Roller Mills
Don Allison Equipment, Inc.
233 Melville Road, Arley, AL 35541 [MAP]

Phone: 800-669-6450    Email:
Copyright 2018 © Don Allison Equipment, Inc.
Product specs & information are subject to change without notice.
Email Us!